Setralynx Studio

How to set a contractor hourly rate.

Dividing the income you want by 2,080 hours feels like a full-time year. It is a full-time year of clock hours. It is not a year of hours a customer pays for. The rate only works if the denominator is hours you can actually bill.

Where 2,080 comes from

Forty hours a week times 52 weeks is 2,080 hours. That product counts every week as if you were on a job a customer will pay for: vacation, holidays, sick days, quoting, driving, buying materials, bookkeeping, training, callbacks, and days when the weather or the schedule leaves you idle. Some of those hours are rest. Some are real work. Almost none of them appear as a line on an invoice.

If you set your rate as "income I want, divided by 2,080," you are asking each billed hour to carry only itself. The unpaid hours still cost you a living. The shortfall shows up as a year that felt busy and a bank balance that does not match the rate on your quote.

There is no universal count of billable hours on this page, and no survey result to copy. Trades differ. A shop with office staff bills differently from an owner who writes every quote at the kitchen table. The number you need is yours: hours you expect to sell in the next year, not hours you expect to be awake.

A way to count billable hours without a fake average

Open last quarter's invoices, if you have them. Add the hours those invoices actually charged. Multiply by four for a rough year, then adjust if that quarter was unusually full or unusually empty. If you bill by the job instead of by the hour, estimate how many hours each job took and use that as the billed time. The point is to start from work you were paid for.

Then list the hours that job never covered. A morning on estimates. A parts run. A recall visit you did not charge. A week you took off. Those hours stay out of the denominator. They are why the denominator is smaller than 2,080, not because of a rule of thumb copied from someone else's business.

If you have no invoices yet, pick a billable-hour figure, write down why, and mark it as an assumption. An assumed 1,200 hours is not a fact about your trade. The rate moves when that input moves.

What overhead is doing in the rate

Overhead is the cost that continues when the calendar is empty. Typical categories, not a price list: vehicle costs you do not bill per job (payment, fuel, insurance, repairs), liability insurance, tools that wear out, phone, software, licences, a storage unit or shop rent, and advertising. Materials you buy for a named job usually belong on that job's price. If you bury job materials inside the hourly rate, material-heavy work comes out cheap and labour-only work comes out expensive.

Overhead is not profit, and it is not tax. Profit is what you intend to keep after overhead and after your own pay. Tax depends on where you live and how the business is set up. Check with an accountant before you treat any percentage as your tax. The example below does not include a tax gross-up.

A labelled example, not a recommended rate

Example only. These figures are sample data so the division is visible. They are not a suggested rate for any trade, and they are not an average.

You want $60,000 for yourself for the year. Overhead for the year is $18,000. You expect to bill 1,200 hours, and you wrote down why you chose 1,200. Before any separate profit or tax gross-up, the hours have to cover $78,000. Divided by 1,200, that is $65 an hour.

The same $78,000 divided by 2,080 is $37.50 an hour. Income alone, with overhead left out, is $60,000 divided by 2,080, about $28.85. Both of those figures understate this example. Using 1,200 billable hours produces $65. The work did not get easier. The unpaid hours were simply left out of the 2,080 division.

That $65 still has no extra profit in it, and it has no income tax set aside. If you want the business to keep something above your pay and your overhead, the rate has to be higher than $65 in this example. How much higher is your decision. A calculator that shows each step is safer than doing the gross-up once on a notepad and forgetting which percentage you used.

Use the rate on purpose

Use that rate on hourly work and as the labour input inside flat quotes. If a flat quote assumes four hours and the visit takes seven, fix the hour estimate. Do not cut the rate to make a quote look competitive and hope overhead takes care of itself. Review the inputs when insurance, the truck, or your billed hours actually change.

Use it on the next job.

  • Open the free hourly rate calculator. Enter the pay you want, the hours you can bill, overhead, a tax set-aside, and profit. Sample numbers on that page are samples. Replace them. The math stays in your browser.
  • Browse the $19 kits. Trade templates for estimates, invoices, and job sheets, sold as instant downloads.
  • See the $497 website. We build a site for a local service business and send the live link before you pay. Keep it for $497 one time, or walk away.